Welcome to iLOQ Support

By using relay outputs K1 and K2 the Key switch can be used, for example, to open and close a roller door. In this scenario, select the Roller door relay mode with dip switches.

Connect the door control buttons to the Relay card using inputs Button1 and Button2. With a valid key in the Key reader:

• The activation of input Button1 activates relay output K1.
• The activation of Button2 activates relay output K2.
• The activation of both Button1 and Button2 at the same time does not activate neither K1 nor K2.

See also Appendix 6 - Wiring Diagram for R10S.3 Roller Door.

You can control relay K2 with a lock cylinder connected to the Cylinder interface of the Relay card. Relay K2 is activated when a valid key is successfully read in the cylinder. A cylinder can only be connected in the Basic configuration and in the Impulse relay mode. You do not have to program the Relay card; relay K2 indicates a valid opening also in the factory state and in the formatted state.

The connected cylinder can be an S10 or Privus. An S10 cylinder does not need to be programmed in the same S10 system as the Relay card.

The default impulse of the K2 relay is 30 seconds, and it can be changed on iLOQ Manager, but this requires the programming of the Relay card. If the Relay card is equipped with the Real-time clock A00.9, and is formatted or programmed, the cylinder receives the time from the Relay card.

See also Appendix 7 - Wiring Diagram for R10S.3 Cylinder.

The Key reader is connected to the Relay card KEY READER connectors, whereupon a green light in the Key reader indicates when the device is powered up (ONLINE LED). The red or green key symbol indicates whether the key, inserted into the Key reader, was approved or rejected (STAT1 G and STAT1 R).

The Key reader also has inputs STAT2 GRN, STAT2 RED and GND for status indications of the device under control. You can bring feedback information these inputs from the device under control in the form of 3.3 – 24 VDC. If no feedback information is received from the device under control, the Relay card can also be connected to control the STAT2 GRN LED. In such cases, the STAT2 output will follow the Relay card relay output K1 status (except when in the Roller door mode).

In cabling, use a data transfer cable, such as MHS 5x2x0.5, should be used. The maximum distance between the Relay card and the Key reader is 100 metres.

The Key reader is connected to the Relay card KEY READER connectors 1-WIRE and GND, in such a way that the Key reader red wire is connected to 1-WIRE, and the black wire to GND. The Relay card also has a mating connector for the Key reader wire connector, which can be used, for example, in the programming stage.

In cabling, use a data transfer cable, such as MHS 5x2x0.5, should be used. The maximum distance between the Relay card and the Key reader is 100 metres.

This section describes the Relay card interfaces.

This section describes how to add a Key Switch on iLOQ Manager.

1. Ensure that the Key Switch is connected and ready for use.
2. Add a formatting task to the token.
   See Adding Formatting Task to Token.
3. Select Basic data > Browse locks.

   

4. Select Add lock.
5. Select Add lock.
6. Enter the necessary information, and select R10S.3.x as Lock cylinder.
7. Select Next.
8. Select the relay configuration in the <Select relay configuration> drop down menu.

   For more information, see Relay Configurations.

9. Select the relay mode in the <Select relay mode> drop down menu.

   See Relay Modes.

10. Enter additional information as necessary.
11. Select Next.
12. Select the access rights for the lock.

    The default access right will be automatically added for the lock.

    1. Select the desired access right in the list on the left.
    2. You can manage the selection of access right with the key buttons as follows:
       • — Click the Arrows right button to move all items to the selection list.
       •  — Click the Arrow right button to move the selected item(s) to the selection list.
       • — Click the Arrow left button to remove the selected item(s) from the selection list.
       •  — Click the Arrows left button to remove all items from the selection list.
13. If necessary, set the lock to handle time limits by checking the Lock handles time limits check box.
    Note:

    If a key is time limited, but the lock does not handle key time limits, the key functions all the time.

14. If you selected other than the Basic relay configuration, a matrix is opened, where you can use check-boxes to select which access right controls each relay.
15. Select Next.
16. Select Next.
17. Select one of the options below:

    • Leave locks in planning state — Select Leave locks in planning state if you want to leave the lock in the planning state, and continue planning the locking system without, for example, programming any physical locks.

    • Order locks — Select Order locks if you know that the lock definitions are final, but you want to program the lock later.

      For more information, see Ordering Locks.

    • Order and program locks — Select Order and program locks:

      • If you know that the lock definitions are final, and you want to program the lock at once.
      • For locks that have not yet been installed on the premises.

      For more information, see Programming Locks.

    • Order and transfer tasks to programmer — Select Order and transfer tasks to programmer if you are deploying a mounted lock, and you want to program it by disconnecting the Programmer from the computer, and taking it to the lock to be deployed. You can only do this for one lock at a time.

      Note:

      In this case, you will have two tasks for the lock: a formatting task on the token and a programming task on the Programmer. Insert the programming cable to the lock, wait for the green status light, and repeat once to get both tasks carried out.

    • Leave locks in planning state — Select Leave locks in planning state if you want to leave the locks in the planning state, and continue planning the locking system without, for example, programming any physical locks.

18. Select Next.
19. Select Ready.
20. Select Close.

The A00.10 Relay card is depicted in the figure below:

The A10.56.1 Key reader is depicted in the figure below:

The A10.56.2 Key reader is depicted in the figure below:

A10.56.1/2 Key reader in brief:

• Surface mounted Key Reader.
• Communication interface for iLOQ A00.10 Relay Card.
• Power ON LED.
• LED indication of Key authentication.
• inputs for LED indication of external device status.
• Cover material: plastic.
• For indoor use. If used outdoors, the Reader must be protected against rain.
  • Weather protection cover A10.84 available as an accessory.
• Key-way direction:
  • A10.56.1: Contact wire downwards (for Scandinavian oval cylinder market).
  • A10.56.2: Contact wire upwards (for Europrofile cylinder market).

The A10.56.4 Key reader is depicted in the figure below:

A10.56.4 Key reader in brief:

• Surface mounted Key Reader.
• Communication interface for iLOQ A00.10 Relay Card.
• Power ON LED.
• LED indication of Key authentication.
• LED indication of external device status.
• Cover material: Stainless steel.
  • Vandal proof.
  • Hard wearing.
• If used outdoors, Key reader must be protected against rain.
  • Weather protection cover A10.84 available as an accessory.
• Key way direction: Contact wire upwards.

This appendix contains the wiring diagram for R10S.3 Basic.