Welcome to iLOQ Support

This chapter describes how to deploy the S10 Online System hardware.

This section describes how to prepare the Net Bridge.

1. Select Administration > Browse network modules.

   

2. Select Add network module.
   The Adding a network module wizard is opened.
3. Select Add network module.
4. Enter the basic information for the network module, as follows:
   • Name — Enter a name for the new network module in this field. Use a descriptive name. You can use, for example, a name that reminds you of the network module location.
   • Type — Select Net Bridge in the drop down menu.
   • License — Select Net Bridge license type. Two new fields become available:
     • Count of reserved bus devices — Define the number of bus devices you are planning to connect to this Net Bridge.
     • Count of connected bus devices — This flow field indicates the current number of connected devices. As we are adding a Net Bridge, the count is 0.
   • Has key programming hot spot — Select this check box if the network module will have at least one Programming Hot Spot connected to it.

   Select the Active radio button. You can select the Not in use radio button if you do not have an active license yet, but you want to configure the network module anyway.

5. Select Next.
6. Select Next.
7. Fill in the network module settings as follows:

   • Service address — Service address is the locking system server address. Accept the suggested address.

   • User ID — Select the User ID for the network module in the drop-down menu.

     If there are no users in the User ID drop-down menu, select Add new network module user to add a new user, and follow the wizard.

     Tip:

     Usually one network module user for each locking system is enough, even with several network modules in use.

   • Password — Enter the Password for the network module user, in this field.

8. Select Next.
9. If necessary, fill in the local network settings.
   If the Net Bridge is located in a network where IP addresses are obtained from a DHCP server, you do not have to fill in the local network settings. However, if this is not the case, ask the required data from the network administrator.
10. Select Next.
11. If necessary, change the number of the firewall port for receiving messages. Ask the required data from the network administrator.
12. Select Next.
13. Connect a memory stick to the computer USB port.
14. Select the Save file to memory stick radio button, and select the disk drive of the memory stick (for example, J:\). The program adds the file name automatically.
    Alternatively, you can select the Save file to disk radio button to save the file onto your hard disk, in the directory of your choice, and copy it to the memory stick later. If this is the case, remember to paste the file to the root directory of the memory stick (not to a subdirectory).
15. Select Next.
16. A summary screen is shown.
17. Select Ready.
18. Type in the locking system master password.
19. Insert the empty token that you took from the token holder, to the Programmer socket.
    Ensure that the token clicks to its place.
20. Wait until the token is programmed.
21. Insert the login token to the the Programmer socket.
    Ensure that the token clicks to its place.
22. Select Close.
23. Insert the token to the token holder in the Net Bridge.
24. Insert the memory stick to the Net Bridge USB port.
25. Switch the  switch to ON.
    1. An internal test procedure is started.
    2. Check that the USB indicator blinks green five times, indicating that it is reading data from the memory stick. It it does not blink green, the Net Bridge cannot read the memory stick. If this is the case, try to add the Net Bridge with another memory stick, or format the memory stick to the FAT32 file system.
    3. Constant green FUNC, SYSTEM STATUS and possibly SERVER CONN. are illuminated to indicate that the server connection has been successfully tested.
26. If SERVER CONN. is illuminated green, the Net Bridge has reported itself to the server.
27. Switch the  switch to STANDBY.
28. The Net Bridge is now ready for use.
29. Place the network module onto the floor plan.
    The procedure is similar to the process of placing locks onto the floor plan. For more information, see section Placing Locks onto a Floor Plan.

This section describes how to connect a Programming Hot Spot.

1. Ensure that the Net Bridge  switch is on STANDBY.
2. Connect a Hot Spot to a prepared Net Bridge, or continue the bus from the last connected bus device on the main bus, according to the connection diagram in iLOQ S10 Online System - Planning Guidelines.
   Note:

   If you continue the bus from another bus device, remember to disable the termination (TERMINATION = OFF) from the device from which you continue the bus.

3. Set the TERMINATION (TERM) dip switch to the ON position, if this bus device will be the last device on this bus branch. Otherwise, set it OFF.
4. Write down the serial number of the Hot Spot.
5. When you have also connected the other bus devices, finalize the Net Bridge configuration once (see Finalizing the Bus Device Configuration on Net Bridge) and continue this procedure.
6. On iLOQ Manager software, check that the connected Hot Spot has been reported to the Net Bridge device list. You can recognize the Hot Spot by its serial number.

his section describes how to connect a lock cylinder to be remotely managed.

1. Ensure that the Net Bridge  switch is on STANDBY.
2. Connect Door Module to a prepared Net Bridge, or continue the bus from the last connected bus device, according to the connection diagram in iLOQ S10 Online System - Planning Guidelines.
   Note:

   If you continue the bus from another bus device, remember to disable the termination (TERMINATION = OFF) from the device from which you continue the bus.

3. Connect a programmed lock cylinder to the CYLINDERS L1 or L2 connector on the Door Module, according to the connection instructions.
4. Set the operation mode 2 by the OPTIONS dip switches as follows:

   S1	ON
   S2	ON
   S3	OFF
   S4	OFF
   S5	OFF

5. Set the TERMINATION (TERM) dip switch to the ON position, if this bus device will be the last device on this bus branch. Otherwise, set it OFF.
6. When you have also connected the other bus devices, finalize the Net Bridge configuration once (see Finalizing the Bus Device Configuration on Net Bridge) and continue this procedure.
7. On iLOQ Manager software, check that the orange background color for the lock has disappeared from the lock grid view. Remember to refresh the grid view by pressing F5.

This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be calendar controlled.

1. Ensure that the Net Bridge  switch is on STANDBY.
2. Connect Door Module to a prepared Net Bridge, or continue the bus from the last connected bus device, according to the connection diagram in iLOQ S10 Online System - Planning Guidelines.
   Note:

   If you continue the bus from another bus device, remember to disable the termination (TERMINATION = OFF) from the device from which you continue the bus.

3. Connect an electric lock control to the relay output K1 or K2, according to the electric lock manufacturer's instructions.
   Note:

   Do not use the bus power (DC+, DC-) for powering the electric lock.

4. Set the operation mode 2 by the OPTIONS dip switches as follows:

   S1	ON
   S2	ON
   S3	OFF
   S4	OFF
   S5	OFF

5. Set the TERMINATION (TERM) dip switch to the ON position, if this bus device will be the last device on this bus branch. Otherwise, set it OFF.
6. When you have also connected the other bus devices, finalize the Net Bridge configuration once (see Finalizing the Bus Device Configuration on Net Bridge) and continue this procedure.
7. On iLOQ Manager software, check that the connected Door Module has been reported to the Net Bridge device list. You can recognize the Door Module by its serial number.
8. Set the connected relay as a calendar controlled door. See Adding Calendar Controlled Doors
9. Add the calendar, unless you already have a suitable calendar for the door. See Adding a Door Control Calendar.
10. Add the control to the calendar, unless you already have a suitable calendar with controls. See Adding a Direct Control to a Calendar.
11. Attach the calendar to the door. See Attaching Calendars to Calendar Controlled Doors.

This section describes how to connect an electric lock, magnet lock or strike plate, and so on, to be code-access group controlled.

1. Ensure that the Net Bridge  switch is on STANDBY.
2. Connect Door Module to a prepared Net Bridge, or continue the bus from the last connected bus device, according to the connection diagram in iLOQ S10 Online System - Planning Guidelines.
   Note:

   If you continue the bus from another bus device, remember to disable the termination (TERMINATION = OFF) from the device from which you continue the bus.

3. Connect an RFID reader (with a keypad) to the READER RS-485 bus on the Door Module, according to the connection diagram.
4. Connect an electric lock control to the relay output K1 or K2, according to the electric lock manufacturer's instructions.
   Note:

   Do not use the bus power (DC+, DC-) for powering the electric lock.

5. Set the operation mode 2 by the OPTIONS dip switches as follows:

   S1	ON
   S2	ON
   S3	OFF
   S4	OFF
   S5	OFF

6. Set the TERMINATION (TERM) dip switch to the ON position, if this bus device will be the last device on this bus branch. Otherwise, set it OFF.
7. Write down the serial number of the Door Module.
8. When you have also connected the other bus devices, finalize the Net Bridge configuration once (see Finalizing the Bus Device Configuration on Net Bridge) and continue this procedure.
9. On iLOQ Manager software, check that the connected Door Module has been reported to the Net Bridge devices list. You can recognize the Door Module by its serial number.
10. Set the connected relay as a calendar controlled door. See Adding Calendar Controlled Doors
11. Add the calendar, unless you already have a suitable calendar for the door. See Adding a Door Control Calendar.
12. Add the code-access group control to the calendar, unless you already have a suitable calendar with controls. See Adding a Code-access Group Control to a Calendar.
13. Attach the calendar to the door. See Attaching Calendars to Calendar Controlled Doors.

This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be controlled by a Key Reader or an RFID Reader.

1. Ensure that the Net Bridge  switch is on STANDBY.
2. Add, format and program the Door Module to the lock list as a Key Switch.

   Select the type of lock cylinder as N102.

   Select the type of lock as Networked.

3. Connect Door Module to a prepared Net Bridge, or continue the bus from the last connected bus device, according to the connection diagram in iLOQ S10 Online System - Planning Guidelines.
   Note:

   If you continue the bus from another bus device, remember to disable the termination (TERMINATION = OFF) from the device from which you continue the bus.

4. Connect the Key Reader or RFID Reader to the Door Module READER RS-485 bus according to the connection diagram.
5. Connect an electric lock control to the relay output K1, according to the electric lock manufacturer's instructions.
   Note:

   Do not use the bus power (DC+, DC-) for powering the electric lock.

6. Set the operation mode 3 by the OPTIONS dip switches as follows:

   S1	ON
   S2	ON
   S3	OFF
   S4	OFF
   S5	OFF

7. Set the TERMINATION (TERM) dip switch to the ON position, if this bus device will be the last device on this bus branch. Otherwise, set it OFF.
8. When you have also connected the other bus devices, finalize the Net Bridge configuration once (see Finalizing the Bus Device Configuration on Net Bridge) and continue this procedure.
9. On iLOQ Manager software, check that the orange background color for the lock has disappeared from the lock grid view. Remember to refresh the grid view by pressing F5.

This section describes how to control an alarm system by a Key Reader or an RFID Reader.

1. Ensure that the Net Bridge  switch is on STANDBY.
2. Add, format and program the Door Module to the lock list as a Key Switch.

   Select the type of lock cylinder as N102.

   Select the type of lock as Networked.

3. Connect Door Module to a prepared Net Bridge, or continue the bus from the last connected bus device, according to the connection diagram in iLOQ S10 Online System - Planning Guidelines.
   Note:

   If you continue the bus from another bus device, remember to disable the termination (TERMINATION = OFF) from the device from which you continue the bus.

4. Connect the Key Reader or RFID Reader to the Door Module READER RS-485 bus according to the connection diagram.
5. If you connected the Key Reader, terminate it by setting the TERMINATION dip switch to the ON position.
6. Connect an alarm control to the relay output K1, according to the alarm system manufacturer's instructions.
7. If you connected the Key Reader, you can connect the alarm system status information to control the lowermost light of the Key Reader, to indicate the alarm system status.

   Connect the alarm system status information to the Door Module IN 1 to control green light, and/or IN 2 to control red light.

   The status information you bring from the alarm system must be potential-free.

8. Set the operation mode 5 by the OPTIONS dip switches as follows:

   S1	OFF
   S2	ON
   S3	OFF
   S4	OFF

9. Set the TERMINATION (TERM) dip switch to the ON position, if this bus device will be the last device on this bus branch. Otherwise, set it OFF.
10. When you have also connected the other bus devices, finalize the Net Bridge configuration once (see Finalizing the Bus Device Configuration on Net Bridge) and continue this procedure.
11. On iLOQ Manager software, check that the orange background color for the lock has disappeared from the lock grid view. Remember to refresh the grid view by pressing F5.

This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be controlled by a combination of a key and a PIN-code. In this connection, you use a Key Reader and a keypad (RFID reader equipped with a keypad).

1. Ensure that the Net Bridge  switch is on STANDBY.
2. Add, format and program the Door Module to the lock list as a Key Switch.

   Select the type of lock cylinder as N102.

   Select the type of lock as Networked.

3. Connect Door Module to a prepared Net Bridge, or continue the bus from the last connected bus device, according to the connection diagram in iLOQ S10 Online System - Planning Guidelines.
   Note:

   If you continue the bus from another bus device, remember to disable the termination (TERMINATION = OFF) from the device from which you continue the bus.

4. Connect the Key Reader to the Door Module READER RS-485 bus according to the connection diagram.

   Ensure that the TERMINATION dip switch on the Key Reader is OFF.

5. Connect the RFID reader (with a keypad) to the Key Reader RS-485 OUT connector according to the connection diagram.
6. Connect an electric lock control to the relay output K1, according to the electric lock manufacturer's instructions.
   Note:

   Do not use the bus power (DC+, DC-) for powering the electric lock.

7. Set the operation mode 3 by the OPTIONS dip switches as follows:

   S1	ON
   S2	ON
   S3	OFF
   S4	OFF
   S5	OFF

8. Set the TERMINATION (TERM) dip switch to the ON position, if this bus device will be the last device on this bus branch. Otherwise, set it OFF.
9. When you have also connected the other bus devices, finalize the Net Bridge configuration once (see Finalizing the Bus Device Configuration on Net Bridge) and continue this procedure.
10. On iLOQ Manager software, check that the orange background color for the lock has disappeared from the lock grid view. Remember to refresh the grid view by pressing F5.
11. Add the key PIN-code calendar, unless you already have a suitable key PIN-code calendar for the lock. See Adding a Key PIN-code Calendar.
12. Attach the key PIN-code calendar to the lock. See Attaching a Key PIN-code Calendar to Locks.

This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be controlled by a combination of an RFID key and a PIN-code. In this connection, you use an RFID reader equipped with a keypad and a key equipped with an RFID chip.

1. Ensure that the Net Bridge  switch is on STANDBY.
2. Add, format and program the Door Module to the lock list as a Key Switch.

   Select the type of lock cylinder as N102.

   Select the type of lock as Networked.

3. Connect Door Module to a prepared Net Bridge, or continue the bus from the last connected bus device, according to the connection diagram in iLOQ S10 Online System - Planning Guidelines.
   Note:

   If you continue the bus from another bus device, remember to disable the termination (TERMINATION = OFF) from the device from which you continue the bus.

4. Connect the RFID Reader equipped with a keypad, to the Door Module READER RS-485 bus according to the connection diagram.
5. Connect an electric lock control to the relay output K1, according to the electric lock manufacturer's instructions.
   Note:

   Do not use the bus power (DC+, DC-) for powering the electric lock.

6. Set the operation mode 3 by the OPTIONS dip switches as follows:

   S1	ON
   S2	ON
   S3	OFF
   S4	OFF
   S5	OFF

7. Set the TERMINATION (TERM) dip switch to the ON position, if this bus device will be the last device on this bus branch. Otherwise, set it OFF.
8. When you have also connected the other bus devices, finalize the Net Bridge configuration once (see Finalizing the Bus Device Configuration on Net Bridge) and continue this procedure.
9. On iLOQ Manager software, check that the orange background color for the lock has disappeared from the lock grid view. Remember to refresh the grid view by pressing F5.
10. Add the key PIN-code calendar, unless you already have a suitable key PIN-code calendar for the lock. See Adding a Key PIN-code Calendar.
11. Attach the key PIN-code calendar to the lock. See Attaching a Key PIN-code Calendar to Locks.